Signal Dynamics Switch Cubes Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Síťové přepínače Signal Dynamics Switch Cubes. Contents Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 23
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
1
Contents
Introduction Page 2
Instrumentation Page 7
Operation / Function Page 9
Programming Page 18
Appendix Page 21
All Rights Reserved. Reproduction by any means, electronic or mechanical
including photocopying, recording or by any information storage and retrieval
system or translation in whole or in part is not permitted without written
authorization from Signal Dynamics Corporation.
Copyright © Signal Dynamics Corporation.
Installation Page 3
Wire Diagram Page 22
Warranty Page 24
Zobrazit stránku 0
1 2 3 4 5 6 ... 22 23

Shrnutí obsahu

Strany 1 - Contents

1 ContentsIntroduction Page 2Instrumentation Page 7Operation / Function Page 9Programming Page 18Appendix Page 21All Rights Reser

Strany 2 - Introduction

10Switches:The handlebar switches are designed for easy installation or removalwith plug-in connector. They are also LED back-lit for easier buttonide

Strany 3 - Installation

11Right Handlebar Switch Module Functions Operation / FunctionRight TurnStarts or cancels right turn signalfunction. (See turn signal functionbelow)S

Strany 4 - Installation

12Initial LINX™ Power-UP & StartingKey Switch Operation: When the key switch is turned on, power is applied to the LINX™system and a self-test wil

Strany 5 - Installation

13the start button on the right handlebar switch to initiate the enginestarter. The starter motor can not be accidentally engaged if the LINX™system r

Strany 6

14Information & Alert ConditionsText information window:The Text information window is located at the bottom of the LCDscreen. To toggles between

Strany 7 - Instrumentation

15LightingMarker Lights:Turn Signal Lights also function as marker lights.This function enables single intensity incandescent or LED bulbs to havea ma

Strany 8 - Instrumentation

16Turn Signal Function: The turn signal selection buttons are located on the left and right handlebar switch cubes. The turn signals are activated by

Strany 9

17• Brake Lights: When the brakes are applied and themotorcycle is stopped, the brakes remain on until thebike accelerates. This will also cause the t

Strany 10 - Operation / Function

18Program Mode:To enter the program mode, the bike’s run/kill switch must be in “kill”position. After selecting “kill”, the press ( * ) and ( # ) toge

Strany 11 - Operation / Function

19• Vehicle Identification Number - Set or View VIN# (Vin # mayonly be set once on some bikes).• View Logs - This will display a history of “events”

Strany 12

2LINX™ Network Bus Electrical SystemSystem Overview:Simpler, easier installation and comprehensive rider information; theseare the some of the basic a

Strany 13

20Voltage/Temperature are displayed) This will take you to ascreen prompting you to press the # button at the beginning of ameasured mile. When you pa

Strany 14

21System Specification:System Power 12VDC 30AmpsOperating Temperatures 32°F to 122°F (0°C to 50°C)Physical Size Front / Rear Modul

Strany 16

24One Year Limited WarrantySignal Dynamics Corporation warranties this product at time of purchaseto be free from defects in materials or workmanship

Strany 17

3Locating Rear ModuleThe rear module is identified by its’ Black Connector, and should belocated in an area that is close to the battery and Starter S

Strany 18 - Programming

4Installing switch cubesThe switch cubes are designed to fit a 1” handlebar, and connect to thefront brake switch, and clutch switch (optional). Insta

Strany 19 - Programming

5Installing the Display ModuleThe display module can be mounted either above or below the handlebarby attaching the backing plate mounting tab to a ha

Strany 20

6To Replace the Connector End on a Cable.1. Strip about 1” of the outer insulation with an RJ-45stripper/crimping tool, the inner insulation does not

Strany 21 - Appendix

7Display Module: When the system is powered-on, a self-test will run and if any faults arenoted, they will be displayed. After this, the logo will be

Strany 22

8• Temperature and Voltage.• System Alert text message. (If Present)Indicators: The indicator icons are located to the left and right sides of the L

Strany 23 - Warranty

9Front (Tank) ModuleThe following outputs and operations are controlled by the FrontModule:• Ignition • Compression Release• NOS solenoid (optiona

Komentáře k této Příručce

Žádné komentáře